Use this guide if your Z-Wave hub can't install firmware on Swidget inserts (SmartThings, for example). You update the insert from a computer with a Z-Wave USB stick and Silicon Labs Simplicity Studio, then add it back to your hub. If you use Home Assistant, update over the air instead: see Updating a Swidget Z-Wave Insert to Firmware 2.0 (Home Assistant), which keeps the insert's settings.
This route removes the insert from your hub. When you add it back, its settings, associations and automations have to be set up again, so note them before you start.
What you need
- A Z-Wave 800-series USB stick, for example the Zooz ZST39 800 Series Z-Wave USB Stick.
- A Windows, Mac or Linux computer and a free Silicon Labs account.
- The firmware file: firmware 2.0. An insert on 1.7 or older needs firmware 1.8 first: run Step 5 with the 1.8 file, then again with 2.0. Don't install 2.0 directly on 1.7 or older. Versions and what changed: Z-Wave Insert Firmware: Changes by Version.
Inserts accept only firmware signed by Swidget, so a file from anywhere else is refused. Keep the insert powered and the USB stick plugged in for the whole update.
Step 1: Remove the insert from your hub
- In your hub, start removing (excluding) a device.
- Hold the insert's button for 5 to 10 seconds, until the LED turns blue, and let go.
- Check that the hub shows the insert as removed.
Step 2: Set up Simplicity Studio
- Create a free Silicon Labs account at community.silabs.com and confirm it from the email.
- Download Simplicity Studio for Windows, Mac or Linux and install it. This takes several minutes.
- Open it and sign in with your Silicon Labs account (Login, top right). Accept the license agreements when it updates its assets.
Step 3: Install the Z-Wave PC Controller
- In Simplicity Studio, open the Install tab, then Install by Technology Type. If updates are offered, choose Update All and restart Simplicity Studio.
- Open Install by Technology Type again, select 32-bit MCU (or Silicon Labs Matter), choose Next, leave the setting on Auto and accept the agreements. Restart Simplicity Studio when the packages have installed.
- Under Install, Manage Installed Packages, Tools, check that Z-Wave PC Controller is installed.
Step 4: Add the insert to the USB stick
- Plug the USB stick into the computer (directly, not through a USB hub).
- In Simplicity Studio, open Tools, choose Z-Wave PC Controller, then the gear icon at the top right. Select your USB stick (choose Refresh if it isn't listed).
- Start inclusion (add) in the PC Controller, then hold the insert's button for 5 to 10 seconds, until the LED turns blue, and let go.
- The insert appears in the PC Controller's device list.
Step 5: Update the firmware
- Select the insert in the device list and open OTA Firmware Update. Don't use OTW Firmware Update: that updates the USB stick itself.
- Choose the firmware file you downloaded and start the update. The progress shows at the bottom of the window.
- When it finishes, the insert checks the file, installs it and restarts by itself.
Step 6: Add the insert back to your hub
- In the PC Controller, check the insert's firmware version under Network Management.
- Start removing (excluding) a device in the PC Controller, then hold the insert's button for 5 to 10 seconds, until the LED turns blue, and let go.
- Unplug the USB stick and add the insert to your hub as usual. Then set up its settings, associations and automations again.
If something goes wrong
The USB stick isn't listed. Try another USB port, plugged straight into the computer.
The insert won't join the USB stick. Make sure it was removed from your hub first. If it still won't join, factory reset it: hold the button for 10 to 15 seconds, until the LED turns red, and let go. Then try Step 4 again.
The update failed or the file was refused. The insert keeps running its old firmware. Check that you used the file linked above and that the insert isn't already on that version, then try again.
The insert doesn't respond after the update. Give it a few minutes. If it still doesn't respond, pull the insert out of its host, wait ten seconds and push it back in. If that doesn't help, contact support.
For settings, association groups and the button and LED behaviour, see Swidget Z-Wave Inserts: Technical Reference. Questions: email support@swidget.com or use the contact form at swidget.com.
Comments
0 comments
Please sign in to leave a comment.